給水體系選用分區給水方法(高中低區)，選用管材低壓區域選用AGR管，高壓區域選用鋼塑管，水泵房設于一期地下室。裝置工程依據其管材及連接方法不同，裝置工藝及監理要點也不同，下面分類介紹幾種

　　一、管道絲扣聯接：

　　1.斷管用砂輪鋸斷管，應格管材放在砂輪鋸卡鉗上，對準畫線卡牢，進行斷管。斷管時壓手柄用力要均勻，不要用力過猛，斷管后要將管口斷面的鐵膜、毛刺鏟除潔凈。用手鋸斷管，應將管材固定在壓力案的壓力鉗內，將鋸條對準畫線，雙手推鋸，鋸條要堅持與管的軸線筆直，推拉鋸用力要均勻，鋸口要鋸究竟，不許扭斷或折斷，以防管口斷面變形。

　　2.套絲將斷好的管材，按管徑尺度分次套制絲扣，一般以管徑15～32mm者套二次，40～50mm者套三次，70mm以上者套3～4次為宜。用套絲機套絲，將管材夾在套絲機卡盤上，留出恰當長度將卡盤夾緊，對準板套號碼，上好板牙，按管徑對好刻度的恰當位置，緊住固定板機，將潤滑劑管對準絲頭，開機推板，待絲扣套到恰當長度，悄悄松開板機。用手藝套絲板套絲，先松開固定板機，把套絲板板盤退到零度，按順序號上好板牙，把板盤對準所需刻度，擰緊固定板機，將管材放在壓力案壓力鉗內，留出恰當長度卡緊，將套絲板悄悄套入管材，使其松緊適度，而后兩手推套絲板，帶上2～3扣，再站到旁邊面扳轉套絲板，用力要均勻，待絲扣行將套成時，悄悄松開板機，開機退板，堅持絲扣應有錐度。

　　二，管道法蘭聯接

　　1.凡管段與管段選用法蘭盤聯接或管道與法蘭閥門聯接者，必須依照規劃要求和工作壓力選用標準法蘭盤。

　　2.法蘭盤的聯接螺栓直徑、長度應契合標準要求，緊固法蘭盤螺栓時要對稱擰緊，緊固好的螺栓顯露絲扣應為2～3扣，不宜大于螺栓直徑的二分之一。

　　3.法蘭盤聯接襯墊，一般給水管(冷水)選用厚度為3mm的橡膠墊，供熱、蒸汽、日子熱水管道應選用厚度為3mm的石棉橡膠墊。墊片要與管徑同心，不得放偏。